What Size O Ring To Repair Gi Joe

G.I. Gary Shows You lot How: Properly Modify a K.I. Joe O-Ring

September xviii, 2022 Author: Gary Viola

If you lot've ever had the 1980s 1000.I. Joe figures, you've had an O-ring break. With the bones pattern established in 1982, the O-ring pattern lasted until 2006 in retail, making this a very common issue. With these figures equally old equally 35 years, the rubber deterioriates and somewhen needs to exist replaced. Follow forth as I (with generous assistance from Medico and Lifeline) alter out Stalker's O-ring with notes on what to to wait for when doing this common maintenance.

I scored this 1982 Stalker at Terrificon.  I got a great deal on it because, not only was the O-ring broken, but he was missing his waist piece.  I've had his waist for a while and have simply been waiting for the right moment to scoop up the residue of the effigy for my collection.

Ok, and then Lifeline and Doc are freaking out to see Stalker in such a deplorable state.  He'southward loaded up onto the stretcher and information technology'south off to piece of work.

Destro the arms dealer has a variety of O-rings to choose from! But with 4 sizes selection, which one do Lifeline and Doc demand?

There are 4 common O-rings  of fractional inch sizes that are used to fix Thousand.I. Joes. (The dash number represents a national standard that I volition reference for the rest of the commodity)

-012 one/2″OD x 3/8″ID (one/16″ cross department)
-013 nine/xvi″OD x 7/16″ID (1/xvi″ cross section)
-110 9/16″OD 10 iii/8″ID (iii/32″ cross department) (Dwelling house Depot / Danco #8)
-111 five/8″OD x 7/16″ID (3/32″ cross section) (Home Depot / Danco #ix)

These are the most readily bachelor O-rings.  In that location'south also metric O-rings that were probably used (more than on this further down) but they aren't as easily obtained. There are websites that exercise sell G.I. Joe specific ones as well. I had a bag and they were exactly the aforementioned as the -111's. I go my O-rings cheaply using manufacturing supplier websites like McMaster.com to buy in bulk of 100.  The Domicile Depot numbers can help you lot in a pinch if you lot're looking for simply i or 2. Bated from size, 1 other thing to consider with O-rings is the durometer of the rubber. Durometer is the softness of the rubber, a smaller number is softer. 70A is the most common, and works well.  Stay abroad from a ninety durometer as they won't stretch at all.  Smaller than a lxx will stretch easily, and may not hold the figure in place (think floppy).  We're looking for something that will hold the figures together and not break the onetime plastic. Sometimes you lot employ the smaller cross section for clearance problems, or less tension.

Common O-ring usage breakdown:
-012 Girl figures (Scarlett, Covergirl, etc.) where clearance is an event (waists are thinner than male figures)
-013 '82-'84 figures where the -111 is a super tight fit, 1992s Talking Battle Commanders
-110 Girl figures
-111 Every other Chiliad.I. Joe effigy

Sometimes people will recommend the -110 in all the early on figures. While this may work for them, I have found that this makes those figures actress tight and still difficult to assemble.

Physician and Lifeline are using a #0 phillips head screwdriver to remove the back screw.  Exist very careful not to strip or pause the screw. Endeavour not to use a worn screwdriver as that tends to strip the caput of the hardware. If you strip the caput you'll be left with few options.  Some people have luck using a pocket-sized prophylactic ring over the tip. If that doesn't work, yous will need to drill the screw out. This requires farthermost caution equally y'all can impairment the torso easily. Also, removing the screw from the breast becomes even more hard.

An example of a screw that the head broke off. Similar to drilling the caput off, you tin can run into how difficult it is to remove.

Accidentally lose the back spiral? Fun fact: the screws that are used in the legs are the same equally the one in the back! I've run across a couple variations in screws across all the figures equally they have been made in a few factories around the world for so many years. Keeping extra figures for parts comes in handy!

Here's what Stalker looks similar with the chest piece removed. Later figures volition take the shoulder swivels beveled, which provide more room for the o-band. This characteristic became common on 1984-1985 figures. I've seen '83 figures with both styles of shoulder swivels, the afterward releases getting the change every bit either a cost saving or ease of assembly change.

A close upwardly of the -013, original, and -111 oring. Notice how the original is closer in size to the -111 and the pinch marks from being squeezed in between the arms and the dorsum postal service. Later on 35 years, its tough to measure out a cleaved o-ring, just the cross department of the o-band is slightly smaller than the -111, and so it would be virtually 2mm or slightly smaller. Probably an 11mm ID 10 15mm OD. I've purchased "Yard.I. Joe" specific O-rings from parts websites, and they could either be the -111 or the metric equivalent, they are that close in measurement.

Hither's a close up of the clearance we take for the O-ring. Because information technology'south tight, using the -013 will be a smarter option as it volition be easier to gather, and these early figures accept brittle plastic.

Beginning step of reassembly starts with hooking the O-ring on the leg hooks and sliding the waist piece down. Information technology'south a little easier with the -013 model, but expect some finagling. Exist gentle, you lot don't want to suspension the crotch.

Loop the O-ring effectually the back's eye post and flip it into the waist.

Pop the artillery and caput in. Even with the thinner O-ring, it's still a tight fit for the arms. Using the thinner model makes assembly easier, the -111 will exert more force and you'll need both easily to keep this from flipping forward sending the artillery and caput flying.

Advisedly pop the chest on. Screw the back screw on using care not to strip the screw or the plastic. Once the screw is seated, yous're all washed! Yo Joe!

Stalker can now go back to the front lines, merely right now, it's time to hitting the commissary for water ice foam and YoJoe! Cola with the ladies.

Here's a close up view of the o-rings again and then you can better see the difference.

Well, there you accept it! M.I. Gary'south definitive guide to irresolute O-rings on your classic (and possibly not then classic) G.I. Joe figures. Don't forget if you have questions or comments, leave them below!

Until next fourth dimension!

Tags: arah, Fixing, 1000.I. Joe, o-ring, straight arm, swivel arm, vintage, yojoe

What Size O Ring To Repair Gi Joe,

Source: http://pintocomics.com/g-i-gary-shows-you-how-properly-change-a-g-i-joe-o-ring/

Posted by: brownforwas.blogspot.com

Share this post